Hi everyone, As I continue to make progress using the tool, I am ready for more precision work requiring me to, for example, cut something exactly in the center of the stock. Assuming I set it up in VCarve properly, I'm struggling with positioning the stock so that the cut actually happens where it is supposed to. In other words, let's say I build a table top panel that's 4'x4' and I want to cut something in the exact center of the top. Beyond eyeballing it, I'm just not spatially aware enough to figure this out on my own! Any advice, tricks, jigs, best practices to share? I understand that the intersection of the two X and Y notches corresponds to 0,0. It's getting my work positioned properly that I can't seem to do reliably. Thanks! Brianhttps://handibot.com/forum/read.php?2,2424,2424#msg-2424Tue, 15 Sep 2026 14:14:32 -0400 Phorum 5.2.22 https://handibot.com/forum/read.php?2,2424,2441#msg-2441 https://handibot.com/forum/read.php?2,2424,2441#msg-2441 Brian King Handibot ForumWed, 10 May 2017 09:12:32 -0400 https://handibot.com/forum/read.php?2,2424,2432#msg-2432 https://handibot.com/forum/read.php?2,2424,2432#msg-2432
What BO describes works great for small items but if you are wanting to align on large parts like the center of a 4x4 ft. a piece of sheet goods then you will really appreciate the laser alignment tool. It is one of those things I don't use all that often but when I need it, it is worth its weight in gold.
A fair substitute for the laser is to install a carving bit while you find your spot and then install the bit you will be cutting with after everything is locked down.

I wrote an instructable on this some time back, it shows a Kickstarter handibot but nothing in how you do this has changed.

[www.instructables.com]]]> Mark Evans Handibot ForumMon, 08 May 2017 01:22:36 -0400 https://handibot.com/forum/read.php?2,2424,2426#msg-2426 https://handibot.com/forum/read.php?2,2424,2426#msg-2426
When really want to be precise--I'll grab a scrap piece of MDF or plywood and bolt it to the base of my handibot. Then I'll pocket out a space that exactly the size of the blank that I want to carve into. In this case, just a 4x4 pocket. Then I can press my blank into the pocket and rest assured that everything is relative to the coordinate system of the handibot.]]> Brian Owen, ShopBot Handibot ForumWed, 03 May 2017 11:40:28 -0400 https://handibot.com/forum/read.php?2,2424,2424#msg-2424 https://handibot.com/forum/read.php?2,2424,2424#msg-2424
As I continue to make progress using the tool, I am ready for more precision work requiring me to, for example, cut something exactly in the center of the stock. Assuming I set it up in VCarve properly, I'm struggling with positioning the stock so that the cut actually happens where it is supposed to. In other words, let's say I build a table top panel that's 4'x4' and I want to cut something in the exact center of the top. Beyond eyeballing it, I'm just not spatially aware enough to figure this out on my own!

Any advice, tricks, jigs, best practices to share? I understand that the intersection of the two X and Y notches corresponds to 0,0. It's getting my work positioned properly that I can't seem to do reliably.

Thanks!
Brian]]> Brian King Handibot ForumWed, 03 May 2017 10:02:47 -0400