I got a itty bitty 1/32" kyocera router bit I would like to try and use but I can't seem to find the recommended speed settings for it? Where would I look or is it just a guess type of thing?https://handibot.com/forum/read.php?2,3207,3207#msg-3207Mon, 09 Mar 2026 17:15:56 -0400 Phorum 5.2.22 https://handibot.com/forum/read.php?2,3207,3216#msg-3216 https://handibot.com/forum/read.php?2,3207,3216#msg-3216
Alternatively you can adjust the max speed settings in FabMo. In the configuration menu under "axis" there are max speed settings that are probably set to 360 inches per minute (the unit that fabmo uses) -- I'd set them to between 60 and 90 ipm for those small bits. I've got a doc on my wiki (getting to test the new page a lot today!! :) : [sites.google.com] This goes into more detail about the motion settings in FabMo


Also--the speed is ultimately set by the code of your file. There should be a command at the top of the file that reads something like this: "MS, 3.0,1.0" This means move 3ips in the X and Y -- 1ips in the Z. I often edit the code directly to save myself the step of reprocessing files in vcarve.]]> Brian Owen, ShopBot Handibot ForumMon, 17 Sep 2018 16:12:58 -0400 https://handibot.com/forum/read.php?2,3207,3215#msg-3215 https://handibot.com/forum/read.php?2,3207,3215#msg-3215 cuervo Handibot ForumMon, 17 Sep 2018 14:58:48 -0400 https://handibot.com/forum/read.php?2,3207,3214#msg-3214 https://handibot.com/forum/read.php?2,3207,3214#msg-3214www.dropbox.com]

For the 1/32" bit, the recommended federate is 1.5 ips in the X and Y -- 0.5 ips in the Z]]> Brian Owen, ShopBot Handibot ForumMon, 17 Sep 2018 13:58:04 -0400 https://handibot.com/forum/read.php?2,3207,3213#msg-3213 https://handibot.com/forum/read.php?2,3207,3213#msg-3213 cuervo Handibot ForumMon, 17 Sep 2018 12:46:52 -0400 https://handibot.com/forum/read.php?2,3207,3212#msg-3212 https://handibot.com/forum/read.php?2,3207,3212#msg-3212sites.google.com]
Let me know if this shows up--I did a lot of updating to the wiki over the weekend while we were taking shelter from the hurricane!

bit profile is linked at the bottom of the article.]]> Brian Owen, ShopBot Handibot ForumMon, 17 Sep 2018 12:16:57 -0400 https://handibot.com/forum/read.php?2,3207,3211#msg-3211 https://handibot.com/forum/read.php?2,3207,3211#msg-3211 Brian Owen, ShopBot Handibot ForumMon, 17 Sep 2018 12:14:05 -0400 https://handibot.com/forum/read.php?2,3207,3210#msg-3210 https://handibot.com/forum/read.php?2,3207,3210#msg-3210 Mark Evans Handibot ForumMon, 17 Sep 2018 11:40:03 -0400 https://handibot.com/forum/read.php?2,3207,3209#msg-3209 https://handibot.com/forum/read.php?2,3207,3209#msg-3209 cuervo Handibot ForumMon, 17 Sep 2018 09:04:23 -0400 https://handibot.com/forum/read.php?2,3207,3208#msg-3208 https://handibot.com/forum/read.php?2,3207,3208#msg-3208
A couple of rules of thumb: generally don’t cut deeper than 1x diameter. For most operations, run the router wide open. If you get any scorching your feed is too slow, too fast has an unique sound that tends to induced panic. :S]]> Mark Evans Handibot ForumMon, 17 Sep 2018 03:24:19 -0400 https://handibot.com/forum/read.php?2,3207,3207#msg-3207 https://handibot.com/forum/read.php?2,3207,3207#msg-3207 cuervo Handibot ForumSun, 16 Sep 2018 20:53:51 -0400