I have been having issues with the Handibot actually following any circles or curves I create in Vcarve. Vcarve Version: 8.517 Handibot Version: 1.2.0 I can upload a sample sbp file if needed, but wanted to check first to see if this is a general issue. Handibot behaves normally whenever it is following straight lines, but simply doesn't cut the curves. If the curve is part of the larger path it simply rapid moves to the next straight line (which is clearly a problem since it's in the material at the time). If there is a curve standing alone, it plunges to the appropriate depth but then pulls right back up and goes to the next plunge location. Thanks,https://handibot.com/forum/read.php?2,3266,3266#msg-3266Tue, 19 May 2026 21:29:16 -0400 Phorum 5.2.22 https://handibot.com/forum/read.php?2,3266,3322#msg-3322 https://handibot.com/forum/read.php?2,3266,3322#msg-3322
I will try to get a video and picture of what's happening.]]> CharlieJanecka Handibot ForumThu, 27 Dec 2018 20:23:50 -0500 https://handibot.com/forum/read.php?2,3266,3316#msg-3316 https://handibot.com/forum/read.php?2,3266,3316#msg-3316
The commands in the file look normal. 1.2.0 is an early version of FabMo and I can't recall if there was an issue with certain types of circle commands in that release of the software. I would recommend getting up to date version 1.6.0 -- instructions for completing the update can be found here: [sites.google.com]

Otherwise, everything looks OK and seems to run OK.

Brian]]> Brian Owen, ShopBot Handibot ForumMon, 17 Dec 2018 15:15:38 -0500 https://handibot.com/forum/read.php?2,3266,3312#msg-3312 https://handibot.com/forum/read.php?2,3266,3312#msg-3312 CharlieJanecka Handibot ForumSat, 15 Dec 2018 13:31:33 -0500 https://handibot.com/forum/read.php?2,3266,3311#msg-3311 https://handibot.com/forum/read.php?2,3266,3311#msg-3311
It starts the curve at it's point but then jumps to the next one.]]> CharlieJanecka Handibot ForumSat, 15 Dec 2018 13:30:50 -0500 https://handibot.com/forum/read.php?2,3266,3272#msg-3272 https://handibot.com/forum/read.php?2,3266,3272#msg-3272Also--Handibot v1.2.0--are you running FabMo on your tool or the older SB3 software? FabMo being the we browser based control system where you access the tool via wireless connection.]]> Brian Owen, ShopBot Handibot ForumTue, 20 Nov 2018 10:53:19 -0500 https://handibot.com/forum/read.php?2,3266,3266#msg-3266 https://handibot.com/forum/read.php?2,3266,3266#msg-3266
Vcarve
Version: 8.517

Handibot
Version: 1.2.0

I can upload a sample sbp file if needed, but wanted to check first to see if this is a general issue. Handibot behaves normally whenever it is following straight lines, but simply doesn't cut the curves. If the curve is part of the larger path it simply rapid moves to the next straight line (which is clearly a problem since it's in the material at the time).

If there is a curve standing alone, it plunges to the appropriate depth but then pulls right back up and goes to the next plunge location.

Thanks,]]> CharlieJanecka Handibot ForumSat, 17 Nov 2018 14:04:56 -0500